EFI bruteforce cold start issues - MudInMyBlood Forums
User Tag List

 
LinkBack Thread Tools Display Modes
post #1 of 12 Old 10-27-2018, 06:09 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
EFI bruteforce cold start issues

I have an 08 750i that has been having issues starting in colder weather (40-50 F) I pretty much have to drain my battery to a pump where it needs a jump to continue trying to start. I eventually get it after using a little starting fluid and itíll start great after that when itís warm.
In warmer weather I donít have to do anything but crank it for a second or two and itís fine.
Shouldnt the ECU compensate for this?
My question is what are some things to check as far as starting issues when cold.
Iíve adjusted the valves with men 10hrs so maybe I need to check that again.


Thanks


Sent from my iPhone using Tapatalk
drewski1126 is offline  
Sponsored Links
Advertisement
 
post #2 of 12 Old 10-28-2018, 08:00 AM
Moderator
 
NMKawierider's Avatar
 
Join Date: Apr 2009
Location: NM
Posts: 7,225
           
With the EFI you won't have the cold starting issues a carbed machine may have as it has fuel right now but..the effects of low compression and/or low fuel pressure will still have an effect on the cold. I suggest you do a compression check...and a fuel pressure check...as the 08s were known to have pump problems...and re-check those valves.

06 BF 750 (Silver) SOLD
15 Z Force 800 EPS


My Videos on You Tube
NMKawierider is offline  
post #3 of 12 Old 10-28-2018, 04:17 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
EFI bruteforce cold start issues

I guess a compression check would kinda let me know if the valves were tight right, should be lower with tight valves Iím assuming.

Iím gonna check that pump out while Iím at it like you said. I checked the follow of it awhile back and it was in range but never did check the pressure.


Sent from my iPhone using Tapatalk
drewski1126 is offline  
Sponsored Links
Advertisement
 
post #4 of 12 Old 01-22-2019, 11:38 AM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
A little update on the troubleshooting Iíve done. Iíve checked all the ignition components and the test out to be within range of the manuals specs. All except the coils. Iím reading 18.3 instead of 10-16 k ohms that the Manual states. Not sure if I need new coils. Iím getting a decent blue spark with iridium plugs.
Iím gonna do the plug wire mod to see if it helps with the starting issues.

Also I checked the compression on the cylinders and they came back 50psi-front and 80psi-rear.
36-66 is the range from the Manual.

Wondering why the rear is so much higher. And if this could attribute to my issues.


Sent from my iPhone using Tapatalk
drewski1126 is offline  
post #5 of 12 Old 01-22-2019, 12:32 PM
Moderator
 
NMKawierider's Avatar
 
Join Date: Apr 2009
Location: NM
Posts: 7,225
           
Quote:
Originally Posted by drewski1126 View Post
A little update on the troubleshooting I’ve done. I’ve checked all the ignition components and the test out to be within range of the manuals specs. All except the coils. I’m reading 18.3 instead of 10-16 k ohms that the Manual states. Not sure if I need new coils. I’m getting a decent blue spark with iridium plugs.
I’m gonna do the plug wire mod to see if it helps with the starting issues.

Also I checked the compression on the cylinders and they came back 50psi-front and 80psi-rear.
36-66 is the range from the Manual.

Wondering why the rear is so much higher. And if this could attribute to my issues.


Sent from my iPhone using Tapatalk
Although it isn't unherad of for them to be over the 66psi, the fact that there is such a difference does tell me there is something afoot. I am assuming you pulled both plugs, held the throttle wide-open on both and that you charged the battery back before doing the other one. If so, then there may be a ring, leaky valve or a spring on one comp release issue. Need to do a leak-down test next. Most often with EFI engines, hard starts are related to either compression or timing issues...of course there are always the possibility of low fuel pressure or supply issues but I'm sure you have checked all that already.


The coils can show higher voltage then the rest of the electrical system usually when there is a grounding problem or the coil is charged but hasn't discharged as it is the ECM or CDI that provides the ground for discharge. Your tester may be providing a ground that it shouldn't .Test the coil voltage with the leads off the coil is always best.

06 BF 750 (Silver) SOLD
15 Z Force 800 EPS


My Videos on You Tube

Last edited by NMKawierider; 01-22-2019 at 12:38 PM.
NMKawierider is offline  
post #6 of 12 Old 01-25-2019, 08:18 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
EFI bruteforce cold start issues

So I was working on installing my plug wires and new sparkys tonight and as I finished up, thought I would recheck the fuel pressure as it had been sometime since I had done so. Well sure enough, the pressure only came up to around 34psi and also dropped down rapidly upon the fuel pump shutting off. New pump is on order.
Pretty sure this is my issue all along. But at least I know every inch of this thing on the bright side.

Thanks for all the tips and Iíll post back when I get it installed.



Sent from my iPhone using Tapatalk
drewski1126 is offline  
post #7 of 12 Old 01-26-2019, 08:58 AM
Moderator
 
NMKawierider's Avatar
 
Join Date: Apr 2009
Location: NM
Posts: 7,225
           
Good luck.

06 BF 750 (Silver) SOLD
15 Z Force 800 EPS


My Videos on You Tube
NMKawierider is offline  
post #8 of 12 Old 01-31-2019, 09:12 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
Update:
Got the pump in there and fuel pressure is at 44 psi atm.
Seems to start a little better but still doesnít start right off the bat.
When I jump it with my portable booster set it cranks immediately though. Now Iím wondering if the battery voltage is dropping too low for the ignition to fire causing it not to start.

Anyone know what the minimum voltage for the coils to fire is. ?? Might hook up one of my Jetski batteries to see if that helps it out in the morning.

The battery is a yausa maybe a year or two old. Bought it new when I bought the bike.


Sent from my iPhone using Tapatalk
drewski1126 is offline  
post #9 of 12 Old 02-01-2019, 08:37 AM
Moderator
 
NMKawierider's Avatar
 
Join Date: Apr 2009
Location: NM
Posts: 7,225
           
These coils have a problem charging below 11.5 volts. You may have a bad battery or maybe just a bad connection somewhere. Also, if the starter ever got water in it it will rust-up and pull extra amps pulling the battery down farther and faster.

06 BF 750 (Silver) SOLD
15 Z Force 800 EPS


My Videos on You Tube
NMKawierider is offline  
post #10 of 12 Old 02-01-2019, 01:39 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
EFI bruteforce cold start issues

Ok that does make sense. I was wondering if the starter might be going bad from so many prior starts on the engine.

Another thing I found today while rechecking all the connections and cleaning and applying dielectric grease around the plugs, I found that the coils on both cylinders were wired backwards according to the manual. So I swapped them both and it seems to be starting a little better. Not really sure if this matters or not. Would it really matter if the wires were crossed. ?

Still donít see how it was running to begin with.


Sent from my iPhone using Tapatalk

Last edited by drewski1126; 02-01-2019 at 05:42 PM.
drewski1126 is offline  
post #11 of 12 Old 02-01-2019, 02:48 PM
Newbie
 
Join Date: Jan 2019
Posts: 29
 
as a rule of thumb with any ECM engine. if you connect an electrical meter and set it to minimum VDC. crank the machine and if it dips under 9vdc you need a new battery. under 9vdc you start loosing electronics, relays, ecms. there cut off voltage is usually about 9vdc. if you dont have a meter with min/max just attach the probes to battery and watch the meter cranking.
jeff919 is offline  
post #12 of 12 Old 02-04-2019, 06:44 PM Thread Starter
Trail Rider
 
drewski1126's Avatar
 
Join Date: Jan 2018
Posts: 42
 
Quote:
Originally Posted by jeff919 View Post
as a rule of thumb with any ECM engine. if you connect an electrical meter and set it to minimum VDC. crank the machine and if it dips under 9vdc you need a new battery. under 9vdc you start loosing electronics, relays, ecms. there cut off voltage is usually about 9vdc. if you dont have a meter with min/max just attach the probes to battery and watch the meter cranking.


Thanks for that info. I was wondering what the actual cut off was.


Update:
While I was reading on another post, I read that the coils need to have at least 10.5 V to operate correctly. Well after seeing that And testing it on my quad, I found that I was dipping below the 10.0 V range from the battery while cranking. So I decided to check my starter and see if there were any issues in there causing it to draw excess amperage pulling the battery voltage down. I found some amount of corrosion on the hot wire to the starter and cleaned that up. Took the starter apart, cleaned all the dust from the brushes wearing in, and put it back together. Also cleaned the contacts on the back of the stator where the brushes make contact. And the starter spins so much more freely now that when cranking it only drops down to about 11v.
And as of now Iím getting good results starting. The bike starts right up and runs great. Keeping fingers crossed that Iíve fixed all the issues that have kept my bike from being easy to start.




Sent from my iPhone using Tapatalk
drewski1126 is offline  
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the MudInMyBlood Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
2001 sportsman 500 HO wont start with start button bullochboy Polaris 5 04-06-2017 05:29 PM
2006 brute 750 no start prairiedog357 Kawasaki 1 08-13-2016 09:50 PM
Prairie 700 Bog and Die then No Start after warmed Up frankpkp Kawasaki 7 08-02-2016 06:24 AM
2000 Polaris Magnum 325 4x4 stalled and now won't start!!!! Scottlabuff Polaris 0 04-13-2016 04:58 AM
Intermittent electrical issues nate.jager1993 Kawasaki 7 03-13-2016 11:11 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome